a. Relay Division (1) Distribution relay testing (a) Overcurrent (b) Reclosures (2) Transmission Line relay testing (a) Impedance (b) Differential (3) Power circuit breaker timing (4) Use of electronic test instruments (a) Oscilloscope (b) Function Generator (c) Electronic relay test equipment (5) Protective relay circuit testing

a. Safety meeting and equipment inspection b. Transformers (placement, installing and connection) c. Network protectors (installing, testing and repairing) d. Cables (loading, setting, pulling, removal, and sealing primary and secondary) e. Secondary services (racking, IWCB and connections) f. Cable splicing (high voltage, poly and lead) g. Cable terminating (high voltage, poly and lead) h. Self contained cable i. Pipe type cable j. Fault locating (hypotronics and burning) k. Service installations and CT's l. Manholes, vaults, handholes and ducts m. Clearance procedures and switching n. Rotation and phasing

a. Safety meetings and equipment inspection b. Station wiring c. Laying out construction work from blueprints d. Installation, adjustment, repair and maintenance of switching equipment OCB'S, ACB'S, load interrupters disconnect switches and vacuum breakers e. Wiring and testing of control circuits f. Installation and maintenance of transformers g. Installation and maintenance of rotating equipment, including motors, generators, synchronous condensers, pumps and fans h. Wiring and installation of switchboards and switchboard equipment i. Installation and maintenance of batteries and battery chargers j. Installation and maintenance of high capacity rectifiers k. Installation and maintenance of voltage regulators step regulators and tap changers l. Rotation and phasing m. Clearance procedure: requesting a clearance, pick up and receiving a clearance, tailboard conferences, hot testing, grounding, keep open, hold open, releasing clearances, switching orders, and procedures. n. Capacitor banks: Installation, maintenance and hazards o. Bushings: Installation, repair and complete rebuilding of bushings p. Troubleshooting equipment malfunctions q. Conduit bending, manual hand bender, hydraulic bender, and power hydraulic bender r. Tower climbing and tower rescue s. Ladders, handling and safety t. Power man lift equipment and safety u. Poly cable splicing and terminating v. Vault rescue w. Setting up safe work area, traffic coning and flagging x. Radio communications, operating use of in an emergency y. Use of test equipment, ductor, multimeter, amprobe, megger, von test, SF6 gas test, fault gas test z. Rigging, lifting, moving of heavy objects with mobile truck crane or winches aa. National, State and City Electrical Code ab. Substation and field inspections ac. Protective Devices ad. Isolating and disconnecting devices

a. Safety meetings and equipment inspection b. Transformers (1) Testing (a) Breakdown (b) Core loss (c) Copper loss (d) Impedance (e) Ratio (f) Polarity (g) Tap changers (h) Acceptance testing (2) Winding, Construction of (a) Methods (b) Insulation (c) Types c. Dielectric testing (1) Insulating materials (2) Insulators (3) Rubber goods (4) Bushings d. DC motors and generators (1) Rewinding (2) Locating and correcting faults e. AC motors, generators (1) Rewinding (2) Locating and correcting faults f. Street lights (1) Test repair (2) Rebuilding and upgrade (energy conservation) g. Network protectors (1) Test and inspect (new) (2) Rebuild (3) Modify (wall mount to transformer mount) h. Transformer oil (1) Dielectric test (2) Acid test (3) Operation of purifier (4) Dissolved in oil gas analysis i. Electric operated material handling equipment (1) Batteries (2) Chargers (3) Motors (4) Controls j. Capacitor banks Test, repair, acceptance testing and hazards

a. Safety meetings and equipment inspection b. Troubleshooting and testing c. Transformers (placement, installing and connection) d. Cables (loading, setting up for pulling in or removal and sealing PRI and SEC) e. Cable splicing (high voltage and secondary poly) f. Cable terminating (high voltage and secondary poly) g. Fault locating h. Hypo testing i. Service installations and CT's j. Clearance procedures and switching k. Manholes, vaults, handholes and ducts

a. Safety meetings and equipment inspection b. Poles, crossarms and guying c. Conductors, insulators, switches, cutouts d. Fuses and protective devices e. Transformers, hanging, phasing, testing and banking f. Service installations g. Rigging, splicing and line handling h. Clearance procedures and switching

a. Goals (1) Read City Light drawings (a) Elementary diagrams (b) Connection diagrams (c) Physical installation drawings (d) One line diagrams and operator diagrams (2) Understand the process of preparing, issuing and accounting for construction drawings of electrical installations (3) To enhance the importance of drawing accuracy of drawings, and the need to accurately record any field changes made so that these changes can be incorporated into the final drawings b. Work assignments (1) Preparation of construction drawings from sketches or marked prints prepared by experienced engineers (2) Retrieval of drawings from our drawing files (3) Assisting engineers in the checking for accuracy of drawings prepared by others (4) Assisting engineers in field checkout of electrical installations

a. Reviews of Constructor and Operator safety, clearance, and switching procedures. b. Operation of various types of equipment; relays; protective devices, control circuits, isolating devices, and reclosures. c. Orientation to various locations of equipment d. Generation, Transmission and substation transmission systems e. Unit Substations and stations for commercial customers f. Abnormal, Emergency and outage conditions

a. To provide orientation and familiarization for apprentices with the purpose and operation of the Power Control Center, placing emphasis on the interfacing and interrelation of the respective Power Control Center and field crew functions and responsibilities b. Time will be spent dealing with the Washington State Electrical Workers Safety Rules; The department's Power Dispatching Clearance, Keep Open and Hold Open Procedures; clearances including research, planning, coordination, and issuance; switching; work-order tracking; system operation; mapping; and other dispatching functions

Overview of maintenance, repairs and installation of Hydroelectric Generation Units and their auxiliaries. a. Skagit b. Cedar Falls

Each apprentice shall enroll in and attend classes in the trade for not less than four (4) hours weekly for a minimum of 144 hours per year during the term of apprenticeship.