1. Identification of materials
2. Types of roofs
3. Carrying and placing materials for use of joumeyperson
4. Erection of Hoists
5. Hoisting, loading and unloading all materials and tools
6. Proper clothing and personal protective (safety) equipment
7. Safe work practices
8. Health concerns
9. Fall protection

1. Identification of equipment and materials
2. Regulating the heat of bitumen to roof surfaces
3. Preparing Surface
4. Application of bitumen to roof surfaces
5. Preparing, cutting, placing, fitting, and trimming strips of felt or other membranes to surfaces
6. Preparing, cutting, fitting and trimming insulation boards to surfaces
7. Applying additional layers of materials as required
8. Flashing with bitumens or roofs cement
9. Applying aggregates or ballast over composition and single-ply membranes
10. Installing liners for reservoirs and hazardous waste receptacles
11. Applying single-ply materials as waterproofing, damp-proofing materials
12. Trench safety
13. Burn hazards

1. Types of tiles
2. Marking out areas to be tiled
3. Preparing surface for tiling
4. Laying and fitting tile with proper spacing
5. Cleaning tiles
6. Underlayment for tile roofs
7. Safe work practices

1. Types of materials, including Photovoltaic Shingles Underlayments
2. Punching nail holes, cutting and trimming slate
3. Types of roofs and identification of hips, ridges, valleys, etc.
4. Sealing ridges
5. Flashing
6. Replacing broken or missing slates or shingles
7. Reroofing
8. Dangers of removing asbestos shingles roofs
9. Safe work practices

1. Flashings
2. termination bars
3. felts and single-ply type membranes
4. ballasts
5. caulkings
6. cements
7. insulations
8. aggregates
9. primers
10. emulsions, and all other materials used in roofing
11. waterproofing and damp-proofing that have been awarded to the roofer's jurisdiction

1. Polyvinyl Chloride (PVC) systems
2. Ethylene propylene diene monomer (EPDM) systems
3. Chlorinated polyethylene (CPE) systems
4. Chlorosulfonated polyethylene (CSPE or HYPALON) systems
5. Neoprenes
6. Butyl rubbeers
7. Polyisobutylene (PIB) systems
8. NBP nitrile alloy systems
9. Ethylene interpolymers (EIP) systems
10. Modified systems
11. Photovoltaic Roofing Systems
12. Fastening methods, including termination and compression bars, anchors,
13. and mechanically attached or fully adhered system
14. Ballasts, pavers, walkways
15. Caulking, sealants
16. Reroofing with single-ply systems
17. Safe work practices

1. Reroofing or recovering of existing buildings
2. Proper job setup
3. Safe disposal of debris
4. Unique safety requirements.
5. Safe work practices

Section A­ Introduction 12 hours 1 The Roofing Industry 2. Safety Section B­ Kettle & Tankers 12 hours 3. Kettle Safety 4. Kettles & Tankers 5. Heating Bitumen 6. Delivering Hot Section C­ Tools and Equipment 12 hours 7. Hand Tools 8. Hand and Power Equipment 9. Operating Power Equipment 10. Hoists Section D­ Roof, Decks and Vapor Barriers 12 hours 11. Pitch, Slope, and Types of Roofs 12. Roof Features 11. Decks 12. Vapor Barriers Section E­ Insulation 20 hours 15. Introduction to Insulation 16. Installing Insulation 17. Tapered Insulation 18. Mechanical Fasteners Section F­ Installing Built­Up Roofing 40 hours 19. Roofing Felts 20. Planning and Preparation 21. Starting a BUR 22. Laying and Mopping the Plies 23. Surfacing, Sealants, and Coatings 24. Flashings Section G­ Maintenance and Repair 12 hours 25. Re­roofing 26. Leaks and Repairs Section H­ Waterproofing and Dampproofing 12 hours 27. Waterproofing Dampproofing Section I­ Math for Roofers 6 hours 28. Measurement and Numbers 29. Fractions and Decimals 30. Roofer’s Math Section J­ Reading Prints 6 hours 31. Organization of a Set of Plans 32. Reading Plans and Elevations and Using a Scale 33. Reading Roof Plans and Details

Section I­ Introduction 12 hours 1. Single­Ply Roofing 2. Installation Section II­ EPDM 42 hours 3. Introduction to EPDM 4. EPDM Ballasted System 5. EPDM Mechanically Fastened Systems 6. EPDM Adhered Systems 7. Detailing EPDM Section III­ Hot­Air Welding 36 hours 8. Hot­Air Welded Systems 9. Hot­Air Welding 10. Detailing Hot­Air Welded System Section IV­ General 30 hours 11. Repair and Maintenance 12. Tie­offs and Night Seals Section V­ Other Systems 24 hours 13. Other Single­Ply Systems 14. Liners and Waterproofing 15. Photovoltaic Roofing Systems

1. Introduction to Modified Bitumens 2. Safety 3. Atactic Polypropylene (APP) 4. Styrene Butadiene Styrene (SBS) 5. Methods of Installation 6. Detailing Modified Bitumens 7. Repair & Maintenance 8. Fire Hazards

Working on Steep Slope Roofs 20 hours 1. Safety 2. Steep Slope Roofs 3. Tools and Equipment 4. Hoisting Installing 20 hours 5. Installation Techniques 6. Wood and Shake Shingles 7. Composition Shingles and Fire­resistant Shingles 8. Slate 9. Asphalt Roll Material 10. Tile 11. Photovoltaic Shingles and Systems Maintenance and Repair 20 hours 11. Tear­Off and Reroofing 12. Repairs